Real Time Convolver

Allows you to perform linear convolution between audio signals.

The module can be executed in two different ways:

 selecting the WaveWorks/Real Time Convolver item from the Transform menu.
 by pressing the button with the icon located in the toolbar.

The module dialog box is made up of the following components:

Monitor page
It graphically shows the operations to which the input signal is subjected before it is saved (or pre-listened to). In particular, the input label identifies the waveform that is about to be processed; the red squares represent the channels of the signal in question, where:

M = monaural signal
L = left channel
R = right channel

The IR1 label refers to the impulse response number 1, i.e. any convolutions between the input signal and the impulse response number 1. Also in this case, the blue squares represent the channels of the signal in question, i.e. the impulse response.
Similarly, the IR2 label distinguishes the convolutions between impulse response number 2 and everything that happens "before", with the blue squares indicating the channels of the impulse response considered. The Output label shows the user whether the signal obtained after processing is mono (red square with M) or stereo (squares with L and R). Any adders present between the channels of the response to impulse number 2 and the channels of the output signal mean that, if the results of the convolutions give rise to two "Left" components or two "Right" components, they add to form a single left channel and a single right channel.

IR#1 and IR#2 pages
They graphically show the trend of the two IRs over time, as well as information regarding:

 the IR sampling frequency
 the number of IR channels
 the length in samples of the IR
 the source from which the IR was loaded

The following four buttons appear in the lower part:

Files
By pressing this button the user intends to load an impulse response stored in a file on disk. After pressing the button, the Open File common dialog will appear through which the user can search for the file to upload.
Cool Clips
By pressing this button, the impulse response previously stored in the Cool Edit Clipboard, i.e. in the CoolClipboard.wav file, is loaded into memory and consequently displayed. The default path used by the module to open this file is c:\windows\temp\CoolClipboard.wav; if the file resides in a directory other than the one indicated, a common dialog appears through which the user will specify the path to the file once and for all.

WinClip
By pressing this button, the impulse response previously stored in the Windows Clipboard in the CF_WAVE format is loaded into memory and consequently displayed.
Unload
This button is pressed when the user wants to eliminate the impulse response from memory; if there is no impulse response in the memory, the message Impulse Response Not Loaded appears instead of the graph. Note that just as it is not possible to load IR2 before IR1, it is not allowed to delete IR1 if IR2 resides in memory (a warning message signals these two anomalous situations).

Audio page
Shows the playback capabilities of the currently selected sound card. In the table below, the cells marked with the green Yes entry denote the sound card's ability to reproduce a WAV file at a certain sampling frequency and with a certain number of channels and bits per sample; otherwise the red No entry appears in the cell. The combo box at the top of the page shows a list of sound cards installed on the personal computer and allows the user to select a card capable of correctly reproducing the output audio file.

Status Bar
At the lower end of the left part of the dialog box, under the Tab Control, we find the status bar, which has the task of informing the user about what is happening during the data processing phase (if the Preview button has been pressed). Since the amount of calculations to be carried out is large, it will be useful to know at any time where we are in the processing cycle.

Channels Selector
In this section the user can select the impulse response channels that will be convolved. The selection is made via button-shaped check boxes on which the initial of the response channel appears
pulse (M = mono, L = Left, R = Right). As for the Monitor graphic window, also in this case the labels to the left and right of the check buttons highlight the type of signal at the input (mono or stereo) and at the output, after its processing.
As for the Monitor graphic window, also in this case the labels to the left and right of the check buttons highlight the type of signal at the input (mono or stereo) and at the output, after its processing.
Come per la finestra grafica Monitor,   anche in questo caso le etichette alla sinistra e alla destra dei check buttons evidenziano il tipo di segnale allingresso (mono o stereo) e alluscita, dopo la sua elaborazione.

Input Signal Info
Report the characteristics of the input waveform, in particular:

 sampling frequency
 type of signal (mono or stereo)
 number of samples that make up the signal

Output Signal Info
Report the characteristics of the output waveform, in particular:

 sampling frequency
 type of signal (mono or stereo)
 number of samples that make up the signal
 number of points used to calculate the FFT

Pre-listening section
It is made up of the push button with the Preview label, which actually starts data processing, and a series of buttons through which the user can vary the dB level of the output signal, with consequent variation of the volume in the headphones.

By pressing the << button the level decreases by 10 dB.
By pressing the < button the level decreases by 1 dB.
By pressing the >> button the level increases by 10 dB.

By pressing the > button the level increases by 1 dB.

The text box positioned in the center of the buttons shows the global level of the output signal compared to the original level (0 dB). Once the Preview button is pressed, its label changes to Stop, so that the user can interrupt the pre-listening phase using the same button. Note that the processed signal is continuously sent to the sound card, thus generating a loop that stops only after pressing the Stop button.
